Militec-1 Military Applications

MILITEC-1 has been PROVEN to be the very best lubricant for all firearms. You will see the many reports from law enforcement agencies and others documenting the superior abilities of MILITEC-1. It is not only the very best by far, it is also the least expensive to use. In fact, it is so cheap that even those who do a lot of shooting will be hard pressed to use $1.00 worth of MILITEC-1 per year.

Militec-1 Military Applications

REDUCES FRICTION
PREVENTS JAMMING
CONSTANT LUBRICATION FOR WEAPONS
CAUSES NO MATERIAL BUILD-UP
INCREASES MUZZLE VELOCITY AND ACCURACY
INHIBITS CORROSION
LONG LASTING

MILITEC-1 has been PROVEN to be the very best lubricant for all firearms. You will see the many reports from law enforcement agencies and others documenting the superior abilities of MILITEC-1. It is not only the very best by far, it is also the least expensive to use. In fact, it is so cheap that even those who do a lot of shooting will be hard pressed to use $1.00 worth of MILITEC-1 per year. So how good can it be? Here's how good:

The state police agency of a mid-Atlantic state has been using MILITEC-1 exclusively for 10+ years. Before MILITEC-1, they had experienced 10 malfunctions in the field and an average of two malfunctions per month on their training range. For the past 10+ years they have not had even one malfunction. They tested MILITEC-1 for six months before they made the switch. You can read their report.
The U.S. Shooting Team reported an 11% increase in accuracy (read the letter [see pdf file]) while one of the world's best law enforcement shooting teams credits MILITEC-1 for part of their success (read that letter [see pdf file]). Others also report better accuracy.
Once MILITEC-1 is applied, it is good for over 1,000 rounds with no cleaning necessary. Several reports support this claim.
When you get around to cleaning a weapon, you can throw out your cleaners and solvents. You won't need them anymore. Just use a dry patch to wipe it clean. Cleaning will no longer be a big chore! See what others say. For application instructions, CLICK HERE.
MILITEC-1 also protects against rust and corrosion when used in wet or hot, humid conditions as well as frigid wintry conditions (see the reports on this).
It takes less than one drop to lubricate a handgun for over 1,000 rounds. One ounce of MILITEC-1 supplies 1,000 drops. How do you use so little when you are lubricating the bore and all the mechanisms? Moisten a patch with MILITEC-1 and just apply a very thin film to the metal. Put the patch in a plastic bag to store it and use it over and over.
MILITEC-1 is being used by over 75 military organizations.
MILITEC-1 is approved and is being used by the U.S. Secret Service, Federal Bureau of Investigation, Drug Enforcement Administration, Internal Revenue Service, State Department and many other state and local law enforcement and correctional agencies.
MILITEC-1 has National Stock Numbers (NSNs) and is being stocked by the Defense Logistics Agency (DLA). One Ounce, 100 per case: NSN: 9150-01-9112; Four Ounce, 12 per case: NSN: 9150-01-9114.

Militec-1 Instructions for Military Applications

Below are suggested directions for using Militec-1 in all pistols, shotguns, rifles, automatic weapons, tank guns.

CHARACTERISTICS:

MILITEC-1 Synthetic Metal Conditioner has the unique ability to create a complex, molecular compound within the surface of heated gunmetal. This causes MILITEC-1 to become part of the metal, not merely a temporary coating or a boundary film. There are two main characteristics of this safe new compound. First, it seals and conditions the metal by stiffening (not hardening) the metal surface. Second, it makes the gunmetal self-lubricating under all environmental conditions.

SELF-LUBRICATION:

After a complete application, a MILITEC-1 conditioned firearm is self-lubricating. Self-lubrication gives the firearm's gunmetal the dry lubricity that is required for sustained fire under all environmental conditions. If exposure to dust, sand, or extreme cold is a concern, all excess MILITEC-1 may be wiped away, leaving the firearm's surface metal clean, dry, and constantly lubricated. Please note: Complete corrosion protection and self-lubrication is attained only after both Step One and Step Two (below) are completed.

PREPARATION:

To take full advantage of MILITEC-1's unique properties, start with a clean firearm. Although MILITEC-1 contains a mild detergent that will help with subsequent cleaning, there are no solvents or other hazardous materials in MILITEC-1, so it cannot remove old caked-on fouling and build-up from other lubes. Thus, if a firearm is dirty, you must clean it with a solvent before you proceed. Normal fieldstrip cleaning should be perfectly adequate. If possible, remove the handgrips, clean and prepare.

INITIAL TREATMENT:

Applying MILITEC-1 to a firearm for the first time is a two-step process: (1) Application and (2) Firing.

STEP ONE: APPLICATION. Now that the firearm is clean and dry, apply a light film of MILITEC-1 to all surfaces, including the bore. Burnish/polish MILITEC-1 into exterior surfaces by rubbing rapidly using a cloth lightly dampened with MILITEC-1. Sparingly apply drops into the action, concentrating on springs, moving parts and metal-to-metal contact areas. If your firearm has a magazine, be sure to apply MILITEC-1 both inside and out. Leave a very light film of MILITEC-1 on all surfaces during reassembly. Now proceed to Step Two.
STEP TWO: FIRING. Once you fire your weapon enough times to reach operating temperatures, the heat and friction will activate MILITEC-1, strengthening the bonding process that was started in Step One. While firing, MILITEC-1 creates a self-lubricating, water-repelling, dry compound within the gunmetal.

Additional Application Instructions:

If Step Two is not immediately possible, consider applying low heat to the firearm to facilitate the bonding process until you can perform Step Two. In field conditions, place your lubed firearm in the sun underneath black plastic or a similar ventilated heat source for at least two hours. Alternatively, you may use a heat gun, hairdryer, burnishing or polishing tool to heat the gunmetal. In heat controlled environments, do not exceed 150° F (65° C). In all applications that require heat to condition the firearm, always insure proper ventilation and wear protective clothing. Please consult our MSDS for additional information.

ULTIMATE PROTECTION:

To maximize the effects of MILITEC-1, repeat Step One and Step Two while the firearm is still hot from the first firing session. MILITEC-1's impregnated molecular bond intensifies during the next 2-3 applications on hot gunmetal. MILITEC-1 has now become a physical part of the gunmetal.

SUBSEQUENT APPLICATIONS:

It is important to continue using MILITEC-1 to lubricate your firearm throughout its normal service life. Consistent use of MILITEC-1 will maintain the self-lubricating effect, maximize corrosion protection, and minimize wear on all friction surfaces. Fouling, deposits and metallic debris do not adhere as easily to gunmetal surfaces conditioned with MILITEC-1. Use a safe, inexpensive cleaner or solvent to detail the firearm, if necessary. For maximum corrosion protection, and especially if long-term storage is anticipated, leave a very light film of MILITEC-1 on all surfaces, after both steps or field application procedures are completed.

APPLICABILITY:

MILITEC-1 is recommended for all pistols, shotguns, rifles, automatic weapons, tank guns and artillery of all calibers and sizes. Note: MILITEC-1 will alleviate jamming due to tight tolerances.